Compressive and Flexural Strength Property Enhancement for Fibre Reinforced M30, M50 and M80 Grade Concrete Using Foundry Sand (FS) and Crushed Concrete Waste (CCW)

Authors

  • Pruthviraj S R University B. D.T College of Engineering ( A Constituent College of Visvesvaraya Technological University)
  • Ravi Kumar C M University B. D.T College of Engineering ( A Constituent College of Visvesvaraya Technological University)
  • Yajnodbhavi H M PES Institute of Technology and Management.
  • Maruthi T University B. D.T College of Engineering ( A Constituent College of Visvesvaraya Technological University)
  • Raghavendra S University B. D.T College of Engineering ( A Constituent College of Visvesvaraya Technological University)

DOI:

https://doi.org/10.30564/jcr.v2i2.2594

Abstract

Now days, many research works are carried for all grades of concrete to make the concrete most economical and durable there by adding the supplementary cementitious materials and alternative replacement aggregates. In this research work deals with the experimental investigation of mechanical properties of the M30, M50 and M80 grade concrete by replacing the fine and coarse aggregate by foundry sand and crushed concrete waste respectively. Mix design procedures were followed as per IRC44:2017 guidelines and recommendation. Proper dosage of super plasticizer (SP) was maintained in the concrete to make it better performed. In this present investigation, a Poly Propylene fibre (PPF) of 0.3% by weight of the cement is used. Mechanical properties such as Compressive strength and Flexural Strength were determined by preparing the respective mould sizes for specific test and are cured for 7, 14 and 28 days and result obtained for respective days were tabulated and discussed.  

Keywords:

M30; M50 and M80 grade concrete; Poly-propylene fibres; IRC guidelines; Mechanical properties

References

[1] Sriram Aaleti “Quantifying Bonding Characteristics between UHPC and Normal-Strength Concrete for Bridge Deck Application” Iowa State University,sri@iastate.edu, Follow this and additional works at:https://lib.dr.iastate.edu/ccee_pubs.

[2] Maqtedar M.A.Moid, A.P.Wadekar et al “Study of High Strength Fiber Reinforced Concrete for M80 Grade by using Different Types of Steel Fibre” August 2016 IJSRD - International Journal for Scientific Research&Development| Vol.4,Issue 06,2016|ISSN (online): 2321-0613.

[3] Jayachandra and Shashi kumar.A (2015). “Strength Behaviour of Foundry sand on modified High Strength Concrete” International Journal of Research in Engineering and Technology(IJRET),eISSN:2319-1163|pISSN:2321-7308,Volume:04 Issue:05|May 2015,Available @ http://www.ijret.org.

[4] Puneeth H C and S P Mahendra (2018).“Replacement of Recycled Construction and Demolition Waste Coarse Aggregates in Pavement Quality Concrete”International Journal of Applied Engineering Research ISSN 0973-4562 Volume 13, Number 7 (2018)pp. 139-145 ©Research India Publications. http://www.ripublication.com.

[5] Milind V. Mohod (2015). “Performance of Polypropylene Fibre Reinforced Concrete” IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE)e-ISSN: 2278-1684, p-ISSN: 2320-334X, Volume 12,Issue 1 Ver. I (Jan- Feb. 2015), PP 28-36.

[6] Yazoghli-Marzouk O, N and Vulcano-greullet (2014).“Recycling foundry sand in road construction–field assessment”Construction and Building Materials 61(2014) 69-78http://dx.doi.org/10.1016/j.conbuildmat.2014.

[7] Anagha Kalpavalli and Dr. S. M. Naik (2015). “Use of Demolished Concrete Wastes as Course Aggregates in High Strength Concrete Production” International Journal of Engineering Research & Technology (IJERT) ISSN: 2278-0181, Vol. 4 Issue 07, July2015, www.ijret.org.

[8] Hymavathi S (2016). “A Study on Mechanical Properties of Fibre Reinforced High Strength Concrete”International Journal of Emerging Technologies in Engineering Research (IJETER) Volume 4, Issue 12,December (2016) www.ijeter.

[9] Chandrasekar R and Chilabarasan T (2017). “Development of high strength concrete using waste foundry sand” Journal of Chemical and Pharmaceutical Sciences, JCPS Volume 10 Issue 1 January - March 2017, www.jchps.com.

[10] Devi Prasad and A. Matha Prasad (2017). “An Experimental Study on Mechanical Properties & Development of M50 Grade Self Compacting Concrete (SCC)& Comparison with M50 Conventional Concrete”

[11] International Journal of Engineering Technology Science and Research IJETSR, ISSN 2394-3386 Volume4, Issue 1, January 2017 www.ijetsr.com..

[12] Susan Rego and Ashok Meti (2018). “Compressive Strength of Cube and Pavement Block of Same Concrete Mix Design” International Journal of Scientific Research and Review, Volume 7, Issue 6, 2018 http://dynamicpublisher.org/.

[13] Naveen Arasu and M.Muhammed Rafsal (2018).“Experimental investigation of high performance concrete by partial replacement of fine aggregate by construction demolition waste” International Journal of Scientific & Engineering Research Volume 9, Issue 3, March-2018, http://www.ijser.org.

[14] Divya Srinath and Shashishankar A (2019). “Compressive Strength of Concrete with Construction and Demolition Waste and m-SAND using Additives”International Journal of Recent Technology and

[15] Engineering (IJRTE) ISSN: 2277-3878, Volume-8 Issue-2S10, September 2019.

[16] Natt Makul (2019). “Combined use of untreated-waste rice husk ash and foundry sand waste in high-performance self-consolidating concrete” Received in revised form 22 July 2019; Accepted 28

[17] July 2019,www.journals.elsevier.com/results-in-materials. https://doi.org/10.1016/j.rinma.2019.100014

[18] IRC 44-2017. Concrete Mix Proportioning Indian Road Congress (IRC), New Delhi.

[19] IS 516:1959. Methods of Tests for Strength of Concrete, Bureau of Indian Standards (IS), New Delhi, India.

[20] IS: 12269:1987. 53 Grade Ordinary Portland Cement-Specifications. Bureau of Indian Standards, New Delhi.

[21] IS: 383:1970 (Reaffirmed 1997) Specification for Coarse and Fine Aggregates from Natural Sources for Concrete. Bureau of Indian Standards (IS), New Delhi.

Downloads

Issue

Vol. 2 , Iss. 2 (December 2020)

Article Type

Articles

License

Copyright and Licensing

The authors shall retain the copyright of their work but allow the Publisher to publish, copy, distribute, and convey the work.

Journal of Construction Research publishes accepted manuscripts under Creative Commons Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0). Authors who submit their papers for publication by Journal of Construction Research agree to have the CC BY-NC 4.0 license applied to their work, and that anyone is allowed to reuse the article or part of it free of charge for non-commercial use. As long as you follow the license terms and original source is properly cited, anyone may copy, redistribute the material in any medium or format, remix, transform, and build upon the material.

License Policy for Reuse of Third-Party Materials

If a manuscript submitted to the journal contains the materials which are held in copyright by a third-party, authors are responsible for obtaining permissions from the copyright holder to reuse or republish any previously published figures, illustrations, charts, tables, photographs, and text excerpts, etc. When submitting a manuscript, official written proof of permission must be provided and clearly stated in the cover letter.
The editorial office of the journal has the right to reject/retract articles that reuse third-party materials without permission.

Journal Policies on Data Sharing

We encourage authors to share articles published in our journal to other data platforms, but only if it is noted that it has been published in this journal.