Congratulations to Journal of Building Materials Science for being included in Scopus！
2024-12-10
Experimental Investigation on the Mechanical Properties of Silicone Elastomers Filled with Fumed Silica for Seismic Isolation Bearings
Authors
-
Arthur Ramandalina
Graduate School of Science and Engineering, Saitama University, Saitama 338-8570, Japan
-
Ji Dang
Graduate School of Science and Engineering, Saitama University, Saitama 338-8570, Japan
DOI:
https://doi.org/10.30564/jbms.v7i1.8472Abstract
Laminated elastomeric bearings used in seismic isolation rely on the mechanical properties of their constituent elastomers to ensure effective performance. However, despite their resistance to temperature fluctuations and environmental aggressors, silicone elastomers exhibit relatively low stiffness, limiting their direct applicability in seismic isolation. This study investigates the effect of fumed silica as a reinforcing filler to enhance the mechanical properties of laminated silicone elastomeric bearings. Elastomeric samples were fabricated with varying fumed silica proportions and subjected to Shore A hardness, uniaxial tensile, and lap shear tests to assess the influence of filler content. Additionally, quasi-static tests were conducted on reduced-scale bearing prototypes under combined vertical compression and cyclic horizontal shear to evaluate their seismic isolation performance. The results demonstrate that fumed silica reinforcement significantly increases stiffness, as evidenced by higher Shore A hardness values. However, a trade-off was observed in tensile properties, with reductions in tensile strength and elongation at break. Despite this, the equivalent elastic modulus did not show substantial variation up to large deformations, indicating that stiffness is preserved under most working conditions. Lap shear tests showed that fumed silica improves shear resistance, while quasi-static tests revealed inelastic behavior with small increases in equivalent shear coefficients but no substantial loss in damping ratios. These findings suggest that fumed silica reinforcement enhances silicone elastomers’ stiffness and shear resistance while maintaining moderate damping properties, making it a promising approach for improving the mechanical performance of elastomeric bearings in seismic isolation applications.
Keywords:
Silicone Elastomer; Fumed Silica; Elastomeric Bearing; Seismic Isolation; Experimental StudyReferences
[1] Altalabani, D., Hejazi, F., 2023. Development of rectangular vibration isolators with double core systems for structures. International Journal of Civil Engineering. 21, 763–787. DOI: https://doi.org/10.1007/s40999-022-00801-5
[2] Salvatori, A., Bongiovanni, G., Clemente, P., et al., 2022. Observed seismic behavior of a HDRB and SD isolation system under far fault earthquakes. Infrastructures (Basel). 7(2), 13. DOI: https://doi.org/10.3390/infrastructures7020013
[3] Peng, T., Dong, Y., 2023. Seismic responses of aqueducts using a new type of self-centering seismic isolation bearing. Sustainability (Switzerland). 15(3), 2402. DOI: https://doi.org/10.3390/su15032402
[4] Yin, Z., Sun, H., Jing, L., et al., 2022. Geotechnical seismic isolation system based on rubber-sand mixtures for rural residence buildings: Shaking table test. Materials. 15(21), 7724. DOI: https://doi.org/10.3390/ma15217724
[5] Pan, P., Shen, S., Shen, Z., et al., 2018. Experimental investigation on the effectiveness of laminated rubber bearings to isolate metro generated vibration. Measurement (Lond). 122, 554–562. DOI: https://doi.org/10.1016/j.measurement.2017.07.019
[6] Chen, B., Dai, J., Song, T., Guan, Q., 2022. Research and development of high-performance high-damping rubber materials for high-damping rubber isolation bearings: A review. Polymers. 14(12), 2427. DOI: https://doi.org/10.3390/POLYM14122427
[7] Zhang, R.-j., Li, A.-q., 2020. Experimental study on temperature dependence of mechanical properties of scaled high-performance rubber bearings. Composites Part B: Engineering. 190, 107932. DOI: https://doi.org/10.1016/j.compositesb.2020.107932
[8] Itoh, Y., Gu, H.S., 2009. Prediction of aging characteristics in natural rubber bearings used in bridges. Journal of Bridge Engineering. 14(2), 122–128. DOI: https://doi.org/10.1061/(ASCE)1084-0702(2009)14:2(122)
[9] Li, Y., Ma, Y., Zhao, G., et al., 2023. Study on the basic performance deterioration law and the application of lead rubber bearings under the alternation of aging and seawater erosion. Buildings. 13(2), 360. DOI: https://doi.org/10.3390/buildings13020360
[10] Nishi, T., Murota, N., 2013. Elastomeric seismic-protection isolators for buildings and bridges. Chinese Journal of Polymer Science (English Edition). 31, 50–57. DOI: https://doi.org/10.1007/s10118-013-1217-8
[11] Zhang, Z.J., Zhang, Z.Q., Yue, S., et al., 2023. Performance characteristics of silicone rubber for use in acidic environments. Polymers (Basel). 15(17), 3598. DOI: https://doi.org/10.3390/polym15173598
[12] Han, R., Li, Y., Zhu, Q., et al., 2022. Research on the preparation and thermal stability of silicone rubber composites: A review. Composites Part C: Open Access. 8, 100249. DOI: https://doi.org/10.1016/j.jcomc.2022.100249
[13] Shit, S.C., Shah, P., 2013. A review on silicone rubber. National Academy Science Letters. 36, 355–365. DOI: https://doi.org/10.1007/s40009-013-0150-2
[14] Maghsoudi-Barmi, A., Khaloo, A., Ehteshami Moeini, M., 2021. Experimental investigation of unbonded ordinary steel reinforced elastomeric bearings as an isolation system in bridges. Structures. 32, 604–616. DOI: https://doi.org/10.1016/j.istruc.2021.02.055
[15] Wang, Z., Lin, Y., Li, Z., et al., 2023. Effect of fluorosilicone rubber on mechanical properties, dielectric breakdown strength and hydrophobicity of methyl vinyl silicone rubber. Polymers (Basel). 15(16), 3448. DOI: https://doi.org/10.3390/polym15163448
[16] Clet, J.A.G., Liou, N.S., Weng, C.H., et al., 2022. A parametric study for tensile properties of silicone rubber specimen using the bowden-type silicone printer. Materials. 15(5), 1729. DOI: https://doi.org/10.3390/ma15051729
[17] Wei, C., Hao, X., Mao, C., et al., 2023. The mechanical properties of silicone rubber composites with shear thickening fluid microcapsules. Polymers (Basel). 15(12), 2704. DOI: https://doi.org/10.3390/polym15122704
[18] Yelemessov, K., Sabirova, L.B., Martyushev, N.V., et al., 2023. Modeling and model verification of the stress-strain state of reinforced polymer concrete. Materials. 16(9), 3494. DOI: https://doi.org/10.3390/ma16093494
[19] Zhang, Y., Liu, W., Zhou, Q., et al., 2023. Effects of vinyl functionalized silica particles on thermal and mechanical properties of liquid silicone rubber nanocomposites. Polymers (Basel). 15(5), 1224. DOI: https://doi.org/10.3390/polym15051224
[20] Wang, J., Jia, H., 2022. The Effects of Carbon–silica dual-phase filler on the crosslink structure of natural rubber. Polymers (Basel). 14(18), 3897. DOI: https://doi.org/10.3390/polym14183897
[21] Jung, J.K., Lee, C.H., Son, M.S., et al., 2022. Filler effects on H2 diffusion behavior in nitrile butadiene rubber blended with carbon black and silica fillers of different concentrations. Polymers (Basel). 14(4), 700. DOI: https://doi.org/10.3390/polym14040700
[22] Gupta, S., Esmaeeli, H.S., Moini, R., 2024. Tough and ductile architected nacre-like cementitious composites. Advanced Functional Materials. 34(39), 2313516. DOI: https://doi.org/10.1002/adfm.202313516
[23] K. C, N., Abraham, J., Thomas, M.G., et al., 2024. Carbon nanotube filled rubber nanocomposites. Frontiers in Carbon. 3, 1339418. DOI: https://doi.org/10.3389/frcrb.2024.1339418
[24] Zhao, R.P., Yin, Z.G., Zou, W., et al., 2023. Preparation of high-strength and excellent compatibility fluorine/ silicone rubber composites under the synergistic effect of fillers. ACS Omega. 8(4), 3905–3916. DOI: https://doi.org/10.1021/ACSOMEGA.2C06489
[25] Barrera, C.S., Cornish, K., 2017. Processing and mechanical properties of natural rubber/waste-derived nano filler composites compared to macro and micro filler composites. Ind Crops Prod. 107, 217–231. DOI: https://doi.org/10.1016/J.INDCROP.2017.05.045
[26] Dasaesamoh, A., Khotmungkhun, K., Subannajui, K., 2023. Natural rigid and hard plastic fabricated from elastomeric degradation of natural rubber composite with ultra-high magnesium carbonate content. Polymers (Basel). 15(14), 3078. DOI: https://doi.org/10.3390/polym15143078
[27] Bukit, N., Ginting, E.M., Sidebang, E., et al., 2020. Mechanical properties of natural rubber compounds with oil palm boiler ash and carbon black as a filler. Journal of Physics: Conference Series. 1428, 012020.
[28] Wang, X., Qin, Y., Zhao, C., 2022. High-temperature behavior of silicone rubber composite with boron oxide/calcium silicate. E-Polymers. 22, 595–606. DOI: https://doi.org/10.1515/epoly-2022-0051
[29] Feng, L., Zhou, L., Feng, S., 2016. Preparation and characterization of silicone rubber cured via catalyst-free aza-Michael reaction. RSC Advances. 6, 111648–111656. DOI: https://doi.org/10.1039/C6RA23016D
[30] Dall'Asta, A., Ragni, L., 2006. Experimental tests and analytical model of high damping rubber dissipating devices. Engineering Structures. 28, 1874–1884. DOI: https://doi.org/10.1016/j.engstruct.2006.03.025
[31] Jiang, S., Yong, Z., 2024. Modulation of mechanical properties of silica-filled silicone rubber by cross-linked network structure. Polymers. 16, 2304. DOI: https://doi.org/10.3390/POLYM16162304
[32] Dorigato, A., D'Amato, M., Pegoretti, A., 2012. Thermo-mechanical properties of high density polyethylene - Fumed silica nanocomposites: Effect of filler surface area and treatment. Journal of Polymer Research. 19, 1–11. DOI: https://doi.org/10.1007/S10965-012-9889-2
[33] Rao, V.V., Dixit, P., Krishna, R.H., Murthy, K.R., 2023. Performance evaluation of nano MgO filled polymer material for high voltage insulation. Journal of Surface Investigation. 17, 94–103. DOI: https://doi.org/10.1134/S1027451023010263
[34] Donnet, J.-B., Bansal, R.C., Wang, M.-J., 1993. Carbon black : Science and technology, 2nd ed. Routledge: New York, NY, USA. pp. 289–356.
[35] Liang, T., Yan, C., Zhou, S., et al., 2017. Carbon black reinforced polymethyl methacrylate (PMMA)-based composite particles: Preparation, characterization, and application. Journal of Geophysics and Engineering. 14, 1225–1232. DOI: https://doi.org/10.1088/1742-2140/aa6e7e
[36] Irez, A.B., Bayraktar, E., Miskioglu, I., 2020. Fracture toughness analysis of epoxy-recycled rubber-based composite reinforced with graphene nanoplatelets for structural applications in automotive and aeronautics. Polymers (Basel). 12(2), 448. DOI: https://doi.org/10.3390/polym12020448
[37] Sun, X., Guo, R.F., Shaga, A., et al., 2020. Preparation and characterization of high damage-tolerance nacre-inspired magnesium alloy matrix composites with high carbon nanotube contents. Carbon. 162, 382–391. DOI: https://doi.org/10.1016/j.carbon.2020.02.072
[38] Norouznezhad, M., Janani, H., 2024. Cross-linking network topology and durability in silicone rubber sealants for PEMFCs: The impact of curing systems and nanosilica interactions. Journal of Polymer Research. 31, 1–17. DOI: https://doi.org/10.1007/S10965-024-03898-5
[39] Abedi Koupai, S., Bakhshi, A., Valadoust Tabrizi, V., 2017. Experimental investigation on effects of elastomer components on dynamic and mechanical properties in seismic isolator compounds. Constr Build Mater. 135, 267–278. DOI: https://doi.org/10.1016/j.conbuildmat.2016.12.184
[40] Pöschl, M., Vašina, M., Zádrapa, P., et al., 2020. Study of carbon black types in SBR rubber: Mechanical and vibration damping properties. Materials. 13(10), 2394. DOI: https://doi.org/10.3390/ma13102394
[41] Rutherford, K.J., Akutagawa, K., Ramier, J..L, et al., 2023. The Influence of Carbon Black Colloidal Properties on the Parameters of the Kraus Model. Polymers (Basel). 15(7), 1675. DOI: https://doi.org/10.3390/polym15071675
[42] Ariati, R., Sales, F., Souza, A., et al., 2021. Polydimethylsiloxane composites characterization and its applications: A review. Polymers (Basel). 13(23), 4258.
[43] Rubio-Mateos, A., Rivero, A., Ukar, E., et al., 2020. Influence of elastomer layers in the quality of aluminum parts on finishing operations. Metals (Basel). 10(2), 289. DOI: https://doi.org/10.3390/met10020289
[44] Vacalebre, M., Frison, R., Corsaro, C., et al., 2023. Current state of the art and next generation of materials for a customized intraocular lens according to a patient-specific eye power. Polymers (Basel). 15(6), 1590.
[45] Boldridge, D., 2010. Morphological characterization of fumed silica aggregates. Aerosol Science and Technology. 44(3), 182–186. DOI: https://doi.org/10.1080/02786820903499462
[46] Jin, Y., Zheng, X., Wang, L., et al., 2020. Improved mechanical properties of natural rubber composites reinforced by novel SiO2@HCNFs nanofillers at a low filler loading. Journal of Applied Polymer Science. 137(40), 49225. DOI: https://doi.org/10.1002/app.49225
[47] Haddad, Y.M., Feng, J., 2003. On the trade-off between damping and stiffness in the design of discontinuous fibre-reinforced composites. Composites Part B: Engineering. 34, 11–20. DOI: https://doi.org/10.1016/S1359-8368(02)00076-8
[48] ASTM, 2015. D2240 15. Standard Test Method for Rubber Property-Durometer Hardness 1. https://doi.org/10.1520/D2240-15
[49] ASTM, 2006. D412 06. Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers - Tension.
[50] JIS, 2010. JIS K 6251. Test Method for Vulcanized Rubber - Tensile Test.
[51] AASHTO, 2016. M251 06. Standard Specification for Plain and Laminated Elastomeric Bridge Bearings.
[52] Murota, N., Suzuki, S., Mori, T., et al., 2021. Performance of high-damping rubber bearings for seismic isolation of residential buildings in Turkey. Soil Dynamics and Earthquake Engineering. 143, 106620. DOI: https://doi.org/10.1016/j.soildyn.2021.106620
[53] Sabir, B.B., Wild, S., O'farrell, M., 1998. A water sorptivity test for mortar and concrete. 31, 568–574. DOI: https://doi.org/10.1007/BF02481540
[54] Kabir, H., Wu, J., Dahal, S., et al., 2024. Automated estimation of cementitious sorptivity via computer vision. Nature Communications. 15, 9935. DOI: https://doi.org/10.1038/s41467-024-53993-w
Downloads
How to Cite
Arthur Ramandalina, & Dang, J. (2025). Experimental Investigation on the Mechanical Properties of Silicone Elastomers Filled with Fumed Silica for Seismic Isolation Bearings. Journal of Building Material Science, 7(1), 44–61. https://doi.org/10.30564/jbms.v7i1.8472
Issue
Article Type
Article
License
Copyright © 2025 Arthur Ramandalina, Ji Dang
This is an open access article under the Creative Commons Attribution-NonCommercial 4.0 International (CC BY-NC 4.0) License.
