Amit Saraswat
Mechanical Engineering Department, RKGIT Ghaziabad-201003
Dipak Kumar
RKGIT Ghaziabad affiliated by AKTU Lucknow, UP
The work done in this work deals with the efficacy of cutting parameters on surface of EN-8 alloy steel. For knowing the optimal effects of cutting parameters response surface methodology was practiced subjected to central composite design matrix. The motive was to introduce an interaction among input parameters, i.e., cutting speed, feed and depth of cut and output parameter, surface roughness. For this, second order response surface model was modeled. The foreseen values obtained were found to be fairly close to observed values, showed that the model could be practiced to forecast the surface roughness on EN-8 within the range of parameter studied. Contours and 3-D plots are generated to forecast the value of surface roughness. It was revealed that surface roughness decreases with increases in cutting speed and it increases with feed. However, there were found negligible or almost no implication of depth of cut on surface roughness whereas feed rate affected the surface roughness most. For lower surface roughness, the optimum values of each one were also evaluated.
[1] Sharma, V.S., Dhiman, S., Sehgal, R. and Sharma, S.K., 2008. Assessment and Optimization of cutting Parameters while Turning AISI 52100 Steel. International Journal of Precision Engineering & Manufacturing. 9:54-62.
[2] Fnides, B., Aouici, H. and Yallese, M.A., 2008. Cutting forces and surface roughness in hard turning of hot work steel X38CrMoV5-1 using mixed ceramic. ISSN 1392-1207.
[3] Selvaraj, D.P. and Chandramohan, P., 2010. Optimization of surface roughness of AISI 304 austenitic stainless steel in dry turning operation using Taguchidesign method. Journal of Engineering Science & Technology. 5: 293-301.
[4] Kuram, E., Ozcelik, B., Demirbas, E. and Şık, E., June 30-July 2, 2010. Effects of the Cutting Fluid Types and Cutting Parameters on Surface Roughness and Thrust Force. Proceedings of the World Congress on Engineering Vol. II WCE, London, U.K.
[5] Selvaraj, D.P. and Chandramohan, P., 2010. Influence of cutting speed, feed rate and bulk texture on the surface finish of nitrogen alloyed duplex stainless steels during dry turning. Engineering 2: 453-460.
[6] Hatem, H., 2011. Study the effect of cutting conditions for turning process on the machined surface. Nahrain University, College of Engineering Journal (NUCEJ) 14:61-66.
[7] Sastry, M.N.P., Devi, K.D. and Reddy, K.M., 2012. Analysis and Optimization of Machining Process Parameters Using Design of Experiments. Industrial Engineering Letters. 2:45-50.
[8] Ficici, F., Koksal, S. and Karacadag, M.C., 2012. Optimization of Cutting Parameters for Surface Roughness of Stainless Steel in Drilling Process. International Journal of Advanced Science and Technology. 2:13-26.
[9] Korat, M. and Agarwal, N., 2012. Optimization of different machining parameters of En24 alloy steel in CNC turning by use of taguchi method. International Journal of Engineering Research and Applications. 2:160-164.
[10] Bhateja, A., Bhardwaj, J., Singh, M. and Pal. S.K., 2013. Optimization of different performance parameters i.e., surface roughness, tool wear rate &SK material removal rate with the selection of various process parameters such as speed rate, feed rate, specimen wear, depth of cut in CNC turning of EN24 alloy steel - an empirical approach. The International Journal of Engineering And Science (IJES). 2:103-113.
[11] Ali, M.H., Khidhir, B.A., Ansari, M.N.M. and Mohamed, B., 2013. FEM to predict the effect of feed rate on surface roughness with cutting force during face milling of titanium alloy. Hbrc Journal 9:263-269.
[12] Vipindas, M.P. and Govindan, P., 2013. Taguchi-Based Optimization of Surface Roughness in CNC Turning Operation. International Journal of Latest Trends in Engineering and Technology. 2:11-20.
[13] Kayastha, C. and Gandhi, J., 2013. Optimization of Process Parameter in Turning of Copper by Combination of Taguchi and Principal Component Analysis Method. International Journal of Scientific and Research Publications. 6:3-12.
[14] Tulasiramarao, B., Srinivas, K., Reddy, P.R., Raveendra, A. and Ravi kumar, B.V.R., 2013. Effect of processing parameters on surface finish of the components processed by CNC turning machine. International Journal of Mechanical Engineering Applications Research 4: 15-18.
[15] Das, S.R., Kumar, A. and Dhupal, D., 2013. Effect of machining parameters on surface roughness in machining of hardened AISI 4340 steel using coated carbide inserts. International Journal of Innovation and Applied Studies. 2:445-453.
[16] Sahijpaul, Y. and Singh, G., 2013. Determining the influence of various cutting parameters on surface roughness during wet CNC turning of AISI 1040 medium carbon steel. Journal of Mechanical and Civil Engineering. 7: 63-72.
[17] Patel, M.T. and Deshpande, V.A., 2014. Optimization of machining parameters for turning different alloy steel using CNC-review. International Journal of Innovative Research in Science, Engineering and Technology. 3:1-5.
[18] Begic-Hajdarevic, D., Cekic, A. and Kulenovic, M., 2014. Experimental study on the high-speed machining of hardened steel. Procedia Engineering. 69: 291-295.
[19] Sarıkaya, M. and Abdulkadir Güllü, A., 2014. Taguchi design and response surface methodology-based analysis of machining parameters in CNC turning under MQL. Journal of Cleaner Production.5:604-616.
[20] Kumar, A., Mahapatra, M.M. and Jha, P.K., 2014. Effect of machining parameters on cutting force and surface roughness of in situ Al-4.5%Cu/TiC metal matrix composites. Measurement 48:325-332.
[21] Baskar, N., Vaiysnavan, R., Prabhu, R. and Prakash, R., 2018. Optimization of machining parameters on EN8 material using Genetic Algorithm. International Journal of Engineering Research & Technology. 6:1-5.
[22] Ren, J., Zhou, J. and Zeng, J., 2016. Analysis and optimization of cutter geometric parameters for surface integrity in milling titanium alloy using a modified grey-taguchi method. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 230: 2114-2128.
[23] Pathak, A.D., Warghane, R.S. and Deokar, S.U., 2018. Optimization of cutting parameters in dry turning of AISI A2 tool steel using carbide tool by taguchi based fuzzy logics. Materials Today: Proceedings. 5:5082-5090.
[24] Wang, Z. and Li, L., 2021. Optimization of process parameters for surface roughness and tool wear in milling TC17 alloy using Taguchi with grey relational analysis. Advances in Mechanical Engineering. 13:1-8.
[25] Xiao, M.H., Shen, X.J., Ma, Y., Yang, F., Gao, N., Wei, W.H. and Wu, D., 2018. Prediction of surface roughness and optimization of cutting parameters of stainless steel turning based on RSM. Mathematical Problems in Engineering. 3:1-15.
[26] Pandey, P.C. and Singh, C.K., 2001. Production Engineering and science; Standard Publishers, Distributors, New Delhi.
[27] Amsted, B.H. and Oswald, P.F., 1996. Manufacturing Processes; Willey Publication.
[28] Yaonan, C., Jinlong, Y., Xinmin, F., and Xu, S., 2018. Experimental study on cutting force and process parameter optimization of plunge milling machining of titanium alloy. Tool Engineering. 52: 65-68.
[29] Bolar, G., Das, A. and Joshi, S.N., 2018. Measurement and analysis of cutting force and product surface quality during end-milling of thin-wall components. Measurement 121: 190-204.
[30] Sreejith, P.S., Krishnamurthy, R., Malhotra, S.K., Narayanasamy, K.J., 2000. Evaluation of PCD tool performance during machining of carbon/phenolic ablative composites. Journal of Materials Processing Technology. 104: 53-58.
[31] Seyedbehzad, G., Jean-François, Ch. and Gilbert, L., 2016. Effect of cutting tool lead angle on machining forces and surface finish of CFRP laminates. Science and Engineering of Composite Materials. 23(5): 543-550.
[32] Sheikh-Ahmad, J.Y., 2008. Machining of Polymer Composites, Springer: New York.
[33] Zhang, L.C., 2009. Cutting composites: A discussion on mechanics modelling. Journal of materials processing technology. 209: 4548-4552.
[34] Subramanian, M., Sakthivel, M. and Sudhakaran, R., 2014. Modelling and analysis of surface roughness of AL7075-T6 in end milling process using response surface methodology. Arabian Journal for Science and Engineering. 39: 7299-7313.
[35] Lalwani, D.I., Mehta, N.K. and Jain, P.K., 2009. Extension of Oxley’s predictive machining theory for Johnson and Cook flow stress model. Journal of materials processing technology. 209: 5305-5312.
[36] Subramanian, M., Sakthivel, M., Soorya prakash, K.,et al., 2013. Optimization of end mill tool geometry parameters for Al7075-T6 machining operations based on vibration amplitude by response surface methodology. Measurement. 46: 4005-4022.
[37] Buj-Corral, I., Vivancos-Calvet, J. and Gonza lez-Rojas, H., 2011. Influence of feed, eccentricity and helix angle on topography obtained in side milling processes. International Journal of Machine Tools and Manufacture. 51: 889-897.
[38] Migue-lez, M.H., Zaera, R., Molinari, A., Cheriguene, R., Rusinek, A., 2009. Residual stresses in orthogonal cutting of metals: the effect of thermomechanical coupling parameters and of friction. Journal of Thermal Stresses. 32: 269-289.
